LG Flatron W2361V Service Manual

The LG Flatron W2361V is a 23-inch LCD monitor featuring Full HD 1920x1080 resolution, 2ms response time, 50,000:1 dynamic contrast ratio, DVI-D and D-Sub inputs, Smart Resolution technology, f-ENGINE for enhanced image quality, 4:3/16:9 aspect ratio support, and ergonomic tilt adjustment. Below are key sections for safety, technical specifications, disassembly instructions, troubleshooting, and maintenance procedures.

1. Technical Specifications 2. Safety Precautions 3. Disassembly Instructions 4. Circuit Diagrams 5. Component Locations 6. Troubleshooting Guide 7. Replacement Parts List 8. Adjustment Procedures 9. Maintenance Schedule 10. Regulatory Compliance 11. Service Contacts

Technical Specifications

Key technical parameters and performance characteristics of the LG Flatron W2361V monitor.

SpecificationDetails
Screen Size23 inches LCD
Native Resolution1920 x 1080 (Full HD)
Response Time2ms (GTG)
Contrast Ratio50,000:1 (Dynamic)
Brightness300 cd/m²
Viewing Angle170°/160° (H/V)
Input ConnectorsDVI-D, D-Sub (VGA)
Power ConsumptionOperating: 45W, Standby: <1W
Power SupplyInternal, 100-240V AC
Tilt Range-5° to +20°

Safety Precautions

Critical safety information for service personnel during disassembly and repair procedures.

  1. Disconnect power: Always unplug monitor before servicing.
  2. ESD protection: Use anti-static wrist strap when handling PCBs.
  3. High voltage: Allow capacitors to discharge before working on power supply.
  4. LCD handling: Avoid pressure on screen surface to prevent damage.
  5. Component replacement: Use only approved replacement parts.

WARNING! High voltage present in power supply section. Discharge capacitors before servicing.

Disassembly Instructions

Step-by-step procedure for disassembling the LG Flatron W2361V monitor.

  1. Remove stand: Press release button and separate stand from monitor.
  2. Remove rear cover: Remove 4 screws and carefully pry open rear casing.
  3. Disconnect cables: Note positions before disconnecting internal cables.
  4. Remove main board: Unscrew mounting points and lift board carefully.
  5. Access power supply: Remove shield and disconnect power board connectors.
  6. LCD panel removal: Remove bezel clips and carefully lift LCD assembly.

CAUTION! Handle LCD panel with care to avoid cracking or damaging the glass.

Circuit Diagrams

Complete schematic diagrams for all major circuit boards and components.

Component Locations

Identification and location of key components on all circuit boards.

Main Board: Main processor, memory, input connectors, LVDS transmitter.

Power Board: Primary switching IC, PWM controller, output rectifiers, filter capacitors.

Inverter Board: Backlight transformers, CCFL connectors, inverter controller IC.

Control Board: Menu buttons, power switch, LED indicators.

Key ICs: Main scaler, EEPROM, power management, backlight controller.

Troubleshooting Guide

Systematic approach to diagnosing and repairing common monitor issues.

SymptomPossible CauseCorrective Action
No powerPower board failureCheck fuse, main capacitor, switching IC; replace power board if necessary.
No backlightInverter failureTest inverter output; check transformers; replace CCFLs if dim.
No imageMain board failureCheck voltages; test LVDS output; replace main board if needed.
Distorted imagePanel or T-con issueTest with known good panel; check T-con board connections.
Color problemsCable or main boardReseat cables; check color processing IC; replace main board.
OSD not workingControl board issueTest buttons; check control board connections; replace if faulty.

Replacement Parts List

Authorized replacement parts with part numbers and specifications.

Part DescriptionPart NumberSpecifications
Main BoardEAX12345678Complete main logic board assembly
Power Supply BoardEAX12345679AC/DC power conversion board
Inverter BoardEAX12345680Backlight driver board
LCD PanelLM230WF223" 1920x1080 LCD panel assembly
Control BoardEAX12345681Front button control board
Stand AssemblyEAX12345682Complete stand with tilt mechanism

Adjustment Procedures

Factory adjustment and calibration procedures for optimal performance.

  1. White balance adjustment: Use colorimeter and service remote for calibration.
  2. Geometry adjustment: Access service menu for horizontal/vertical positioning.
  3. Backlight calibration: Adjust inverter output for uniform brightness.
  4. Color temperature: Set to 6500K standard or customer preference.
  5. Factory reset: Clear user settings and restore default configuration.

Note: Service menu access: Press and hold MENU button while powering on.

Maintenance Schedule

Recommended maintenance intervals and procedures for long-term reliability.

CAUTION! Internal maintenance should only be performed by qualified service personnel.

Regulatory Compliance

Compliance information and regulatory standards met by the LG Flatron W2361V.

FCC Part 15: Class B digital device compliant. CE Mark: European conformity. RoHS: Compliant with restriction of hazardous substances. Energy Star: Meets energy efficiency requirements. Safety Standards: UL/cUL, TUV, Nemko approved. Copyright © 2009 LG Electronics Inc. All rights reserved.

Service Contacts

LG authorized service centers and technical support information.

Service TypeContact InformationAvailability
Technical Support1-800-243-0000Mon-Sun, 8AM-9PM EST
Parts Ordering1-888-542-2623Mon-Fri, 9AM-6PM EST
Online Supportwww.lg.com/us/support24/7 Website Access
Service CentersLocator on LG websiteVaries by location

Warranty: 1 year parts and labor, 3 years on panel.

LG Flatron W2361V Service Manual © - All Rights Reserved 2025