LG Dryer DLG2532W Repair Manual

The LG DLG2532W is a 7.3 cubic foot electric dryer with advanced features including Sensor Dry technology, multiple dry cycles, stainless steel drum, reversible door, and energy-efficient operation. This repair manual covers safety precautions, troubleshooting, component replacement, and maintenance procedures for qualified technicians.

1. Safety Precautions 2. Technical Specifications 3. Tools Required 4. Common Symptoms & Diagnosis 5. Component Testing 6. Disassembly Procedures 7. Heating Element Replacement 8. Thermal Fuse Replacement 9. Belt Replacement 10. Motor Replacement 11. Reassembly & Testing

Safety Precautions

Before attempting any repairs, ensure proper safety measures are followed.

Safety MeasureDescription
Power DisconnectionUnplug dryer from electrical outlet before servicing
Gas Line (if applicable)Shut off gas supply valve for gas models
Personal Protective EquipmentWear safety glasses and gloves
Capacitor DischargeDischarge capacitor before handling electrical components
Fire PreventionKeep work area clear of flammable materials
Proper LiftingUse proper lifting techniques; dryer weighs approx. 125 lbs

Technical Specifications

Tools Required

Essential tools for DLG2532W repairs:

  1. Multimeter for electrical testing
  2. Nut drivers (1/4" and 5/16")
  3. Phillips and flathead screwdrivers
  4. Pliers (needle-nose and slip-joint)
  5. Putty knife for panel removal
  6. Socket set
  7. Hex key set

WARNING! Use insulated tools when working with electrical components.

Common Symptoms & Diagnosis

SymptomPossible CauseDiagnostic Steps
No powerPower supply, door switch, thermal fuseCheck outlet voltage, test door switch continuity, test thermal fuse
No heatHeating element, thermostat, thermal fuseTest heating element resistance, check thermostat continuity
Drum not turningDrive belt, motor, idler pulleyInspect belt condition, test motor windings, check idler pulley
Excessive noiseRollers, blower wheel, motor bearingsInspect rollers for wear, check blower wheel balance
Not drying properlyVent blockage, heating element, moisture sensorCheck vent airflow, test heating element, clean moisture sensor

Component Testing

Testing procedures for key components:

  1. Heating Element: Disconnect power, measure resistance between terminals (should be 10-50 ohms)
  2. Thermal Fuse: Test continuity (should be closed circuit)
  3. Thermostat: Test continuity at room temperature (should be closed)
  4. Motor: Test windings for proper resistance values
  5. Door Switch: Test continuity when door is closed
  6. Start Switch: Test for proper contact closure

CAUTION! Always disconnect power before testing electrical components.

Disassembly Procedures

Step-by-step disassembly for DLG2532W:

  1. Unplug dryer and move away from wall
  2. Remove top panel: Insert putty knife at rear corners and release clips
  3. Remove control panel: Remove screws and disconnect wiring harnesses
  4. Remove front panel: Remove screws and carefully pull forward
  5. Remove drum: Release belt tension, lift belt off motor pulley, slide drum out
  6. Access internal components: Heating element, motor, blower assembly

Tip: Take photos during disassembly for easier reassembly.

Heating Element Replacement

Replacement procedure for heating element:

  1. Disconnect power and complete disassembly to access heating chamber
  2. Remove heating element cover screws
  3. Disconnect wiring terminals from heating element
  4. Remove mounting brackets and old heating element
  5. Install new heating element and secure with brackets
  6. Reconnect wiring terminals
  7. Replace cover and reassemble dryer
  8. Test operation before returning to service

WARNING! Ensure all connections are tight to prevent arcing.

Thermal Fuse Replacement

Thermal fuse replacement steps:

  1. Locate thermal fuse on blower housing or exhaust duct
  2. Disconnect wiring connectors
  3. Remove mounting clip or screws
  4. Install new thermal fuse (same temperature rating)
  5. Reconnect wiring and secure mounting
  6. Test dryer operation
  7. Identify and correct cause of overheating

Belt Replacement

Drive belt replacement procedure:

  1. Remove front panel and access drum compartment
  2. Release belt tension by lifting idler pulley
  3. Remove old belt from drum and motor pulley
  4. Route new belt around drum groove
  5. Engage belt with idler pulley and motor pulley
  6. Ensure proper belt alignment and tension
  7. Reinstall front panel and test operation

Note: Belt part number: 5220EL2001B

Motor Replacement

Motor replacement steps:

  1. Complete disassembly to access motor compartment
  2. Disconnect all wiring connectors from motor
  3. Remove mounting bolts and brackets
  4. Remove drive belt from motor pulley
  5. Install new motor and secure with brackets
  6. Reconnect all wiring harnesses
  7. Reinstall drive belt and ensure proper tension
  8. Reassemble dryer and test all functions

Reassembly & Testing

Final reassembly and operational testing:

  1. Reverse disassembly steps for reassembly
  2. Ensure all panels are properly seated and secured
  3. Verify all wiring connections are secure
  4. Plug in dryer and restore power
  5. Test all cycles and functions
  6. Verify proper heating and drum rotation
  7. Check for unusual noises or vibrations
  8. Confirm proper door switch operation

Final Check: Run complete dry cycle with test load to verify proper operation.

Service Support: LG Customer Service 1-800-243-0000; www.lg.com

LG Dryer DLG2532W Repair Manual © - All Rights Reserved 2025