LG DLEX9000V Installation Manual
The LG DLEX9000V is a high-capacity electric dryer with advanced steam technology, sensor drying capabilities, and smart connectivity features. This installation manual provides comprehensive guidance for proper setup, electrical requirements, venting specifications, and initial operation procedures to ensure optimal performance and safety.
Safety Precautions
Before installation, read all safety instructions carefully to prevent injury and property damage.
| Warning Type | Precaution |
|---|
| Electrical Safety | Disconnect power before installation; use dedicated circuit |
| Lifting Safety | Use two people for lifting; avoid back strain |
| Venting Safety | Ensure proper venting to prevent fire hazard |
| Gas Safety | Check for gas leaks if applicable (gas models) |
| Location Safety | Install on level surface away from water sources |
Package Contents
Verify all components are included before beginning installation.
- LG DLEX9000V Dryer Unit
- 4-Wire Power Cord (if required)
- Venting Kit (4-inch diameter)
- Installation Manual
- Warranty Information
- Door Reversal Kit
- Drum Light Cover
NOTE: Contact retailer immediately if any items are missing or damaged.
Installation Requirements
Ensure proper space and utility connections before installation.
- Location: Level, firm floor with adequate clearance (minimum 1-inch sides, 6-inch rear)
- Electrical: 240V, 30-amp dedicated circuit with proper grounding
- Venting: 4-inch rigid metal ducting with maximum 35-foot length
- Ambient Temperature: 40°F to 100°F (4°C to 38°C)
- Moisture Protection: Avoid areas with high humidity or water exposure
Electrical Specifications
Proper electrical connection is critical for safe operation.
| Parameter | Specification |
|---|
| Voltage | 240V AC |
| Frequency | 60Hz |
| Current | 30 Amps |
| Power Cord | 4-wire, NEMA 14-30R |
| Circuit Breaker | 30-amp dual-pole |
| Grounding | Separate equipment grounding conductor required |
WARNING! Installation must comply with local electrical codes. Hire qualified electrician if unsure.
Venting Requirements
Proper venting ensures efficient drying and prevents moisture damage.
- Duct Material: Rigid metal ducting recommended (avoid plastic/flexible)
- Diameter: 4-inch minimum
- Length: Maximum 35 feet (subtract 5 feet for each 90° elbow)
- Exterior Vent: Louvered vent hood with backdraft damper
- Clearance: Minimum 12 inches from exterior wall opening
CAUTION! Improper venting can cause fire hazard and reduced performance.
Step-by-Step Installation
Follow these steps in sequence for proper installation.
- Prepare Location: Clear installation area and ensure level floor
- Install Venting: Connect vent duct to dryer and route to exterior
- Electrical Connection: Connect 4-wire power cord to terminal block
- Position Dryer: Carefully move dryer into final position
- Level Unit: Adjust leveling legs until dryer is stable
- Final Connections: Connect vent duct securely to dryer outlet
- Power On: Restore power and test operation
Leveling and Positioning
Proper leveling ensures optimal performance and reduces vibration.
- Tools Required: Level, adjustable wrench
- Leveling Procedure: Turn leveling legs clockwise to raise, counterclockwise to lower
- Tolerance: Maximum 1° tilt in any direction
- Clearance: Maintain 1-inch side clearance, 6-inch rear clearance
- Anti-tip Bracket: Install included anti-tip device per instructions
NOTE: Excessive vibration indicates improper leveling.
Initial Setup and Testing
Complete these steps before first use.
- Power Verification: Ensure proper voltage at outlet
- Control Panel Test: Verify all buttons and display function properly
- Drum Operation: Run empty cycle to check for unusual noises
- Heating Test: Run warm-up cycle to verify heating element
- Venting Check: Confirm adequate airflow through vent system
- Steam Function: Test steam settings if applicable
- Smart Features: Connect to Wi-Fi and test smart functions
Troubleshooting
Common installation issues and solutions.
| Problem | Possible Cause | Solution |
|---|
| Dryer won't start | Power issue, door not closed | Check power supply, ensure door latches properly |
| No heat | Circuit breaker, heating element | Reset breaker, check heating element connection |
| Excessive vibration | Improper leveling, shipping bolts | Re-level dryer, remove all shipping bolts |
| Poor drying performance | Venting restriction, overload | Check venting for obstructions, reduce load size |
| Error codes displayed | Sensor issues, component failure | Refer to error code chart in manual |
Technical Specifications
- Model: DLEX9000V
- Capacity: 9.0 cu. ft.
- Dimensions (HxWxD): 76" x 32" x 33.5"
- Weight: 185 lbs
- Energy Source: Electric 240V
- Drying Technology: Sensor Dry, Steam Refresh
- Control Type: Electronic with LCD Display
- Connectivity: Wi-Fi, LG ThinQ compatible
- Warranty: 1 year parts and labor, 10 years motor
For technical support: 1-800-243-0000 or www.lg.com
LG DLEX9000V Installation Manual © - All Rights Reserved 2025